Tuesday, November 13, 2012

Creating a Low VOC Dollhouse or Roombox, Part 2

The kitchen
Work-in-Progress

A few days after writing my last post, I had to remove the roombox from my office 
and return it to the garage as the chemicals off-gassing from the plywood were 
making me sick.  The sealer that I used did greatly reduce the fumes, 
but unfortunately, it was not enough.  :( 

I was really disappointed and took a few days to contemplate my very 
limited options and then decided to build a dollhouse out of foamcore. I hope 
I'll be able to make it strong enough to last a long time. 

So far I have the kitchen mostly completed and have ordered the wallpaper for 
the adjoining dining room.  I'm very excited about the progress and will post 
 pics as the process moves along.  In the meantime, do you notice the 
black fridge?  The outside is almost finished and I'll be writing about the 
transformation in a future post.  Until then, happy mini-making, everyone.  
I'm looking forward to catching up on what ya'll have been up to soon.  :)

Sunday, November 4, 2012

Making a Low VOC Roombox or Dollhouse, Part 1

What do you do if a) you realllly want a dollhouse and b) are allergic to the products (MDF and plywood) that most dollhouses are made of?  I developed an allergy/chemical sensitivity to the VOC's (volatile organic compounds) that offgas from MDF and plywood a couple of years ago while making this dollhouse.
Not yet aware that I was allergic to the MDF (I thought
I had a respiratory bug),
I couldn't resist setting up the rooms and playing with
the furnishings prior to painting, papering, and wiring.

Since then, I have been "between dollhouses" as I looked for an affordable alternative that met my requirements for both size (had to fit against a wall like the one above) and number of rooms.   Unable to find one, I turned to trying to find something that would seal in the offgassing vapors, thereby eliminating the problem from its source.

I learned about a product called Safe Seal* that, when applied to the mdf prior to gluing together, painting, or wallpapering, claims to virtually seal in the VOC's  and prevent them from off-gassing into the environment. 

I recently ordered a quart of it from a company here in the U.S. and received it in about a week.  It cost just under $15 which, ironically, was just a few cents less than the cost for shipping.  So for about $30 I'm ready to start my experiment.  (I'm still smarting over paying $15 for shipping to get a $15 item to me, but I had no choice.)
It is a milky liquid about the consistency of water  that goes on easily with a foam brush

If it works, it will be the answer to my dilemna! I tested it on one of a trio of inexpensive roomboxes that have been off-gassing in my garage since I got them as the fumes were too toxic to have them in the house.  If it works on the one, I'll proceed with the other two and then onto a dollhouse!  :)

Here you can see all the pieces laid out on the table which I have protected
with a plastic sheet.  I used weights to flatten out the warpage.

As you can see in the above photo,  once again I couldn't resist 'playing' with the kitchen cabinets and appliances which have been packed away for far too long.  It seems to be a pattern with me when I'm putting together a kit -- work for awhile, then play for awhile.  ;)

So now the big question ~~ did it work?  My current feeling is that it helped significantly although it did not remove the fumes entirely.  I did give each piece, including all of the edges, about half a dozen coats.  The directions state that one coat is usually sufficient, but in this case the fumes were particularly pungent and it took repeated coats to reduce the odor enough that I am hopeful I will be able to tolerate it with the exception of one board -- the first story ceiling/second story floor -- which is a lost cause.  Numerous coats have not been successful in blocking the odors sufficiently and I'm going to have to substitute some foamcore for that piece.  I think foamcore will be ok as I'm not planning on putting anything very heavy in that room.   Perhaps I'll use two pieces of foamcore stacked on top of each other for double strength. 

In conclusion, I'm hopeful that with the exception of that one board mentioned above, the sealer reduced the off-gassing enough that I'll be able to tolerate it in my small workshop.  Let's keep our fingers crossed!

And now more play time- erm, I mean research and development.  ;)

And next time I'll share how I updated a tired and outdated mass-produced fridge from the mid-90's (see above photo for the "before") into something any self-respecting miniature kitchen would be proud to 'wear'.   Ok, that might be an exaggeration, but you can decide for yourself when you see the "after" pic(s) next time. 

Bye for now...  :)

*I do not work for the people who make or sell Safe Seal and I am not being compensated for this write up in any way.  I am merely telling about my experience in the hopes of helping others.*